logo
Bienvenido a ESTEL (GUANGDONG) TECHNOLOGY CO., LTD.
+8613752765943 / 86-0755 23592644

Extending Equipment Lifespan in High-Humidity Fiber Nodes Through Double-Layer Thermal Design

2026/11/17

Últimas noticias de la empresa sobre Extending Equipment Lifespan in High-Humidity Fiber Nodes Through Double-Layer Thermal Design

Extending Equipment Lifespan in High-Humidity Fiber Nodes Through Double-Layer Thermal Design

 

 

Background

 

An FTTH (Fiber to the Home) network operator was expanding its aggregation layer into a humid, subtropical region. The new fiber distribution points were housed in outdoor cabinets situated along main roads and in residential compounds. While the optical equipment itself was robust, the active components—media converters, switches, and power supplies—were failing at a rate higher than the operator's baseline projections.

 

Field investigations revealed a consistent pattern. The failures were concentrated in cabinets that had been installed without adequate thermal insulation. During the day, solar radiation heated the cabinet shell, and the internal temperature rose well above ambient. At night, the temperature dropped, and moisture condensed on the internal components. The repeated cycle of heating and condensation was degrading the electronics.

 

 

The Challenge: Condensation and Heat in Compact Enclosures

 

The operator's engineering team identified two interacting problems.

 

First, the single-wall cabinets used in earlier deployments had minimal thermal resistance. The internal temperature tracked the external temperature closely, leaving the equipment exposed to the full range of daily temperature swings. This was particularly damaging to the power supplies, which were sensitive to thermal cycling.

 

Second, the condensation issue was compounded by the cabinets' cable entry points. While the cabinets were rated for outdoor use, the combination of high humidity and temperature fluctuations created conditions where moisture could accumulate inside the enclosure, especially during the cooler night hours.

 

The operator needed a cabinet design that would stabilize the internal thermal environment without requiring active cooling at every site. Active cooling was reserved for the highest-density locations; for the majority of fiber nodes, a passive thermal strategy was preferable.

 

 

The Solution: Double-Layer Construction with PEF Insulation

 

The operator selected a 25U outdoor cabinet engineered with a double-layer thermal design.

 

1. Insulated Double-Wall Structure


The cabinet uses a 1.2mm outer galvanized steel shell and a 0.8mm inner panel, with 20mm of PEF (Polyethylene Foam) insulation between them. This sandwich construction significantly reduces heat transfer from solar radiation during the day and slows the rate of internal temperature decline at night. The result is a more stable internal environment, with smaller temperature swings and reduced condensation risk.

 

2. IP65 Sealing and Corrosion Resistance


The cabinet is rated IP65, with a fully sealed design that resists dust and water jets. The galvanized steel construction, finished with polyester powder coating in RAL 7035, provides corrosion resistance suitable for humid and coastal environments. The inner hinge design and three-point locking system maintain the seal over repeated maintenance cycles.

 

3. Active Cooling Ready for High-Density Sites


While passive insulation was sufficient for most fiber nodes, the cabinet was designed to accept an optional 1500W air conditioner for sites with higher equipment density. This flexibility allowed the operator to standardize on a single cabinet platform while adjusting the cooling strategy to the specific site requirements.

 

4. Front-Only Maintenance


The cabinet features a single front door with front-only maintenance access. This design simplifies servicing in roadside and residential locations where access to the rear of the cabinet may be limited. A built-in 220VAC LED lamp provides illumination for nighttime maintenance.

 

 

The Results

 

After deploying the double-layer insulated cabinets across the humid region, the operator observed a reduction in thermal-related equipment failures. The internal temperature remained more stable throughout the day, and condensation on the internal components was significantly reduced.

 

The standardized cabinet platform simplified procurement and spares management. Sites with higher equipment density were fitted with the optional air conditioner, while the majority of sites relied on passive insulation alone. This tiered approach kept capital costs under control without compromising reliability.

 

 

What This Case Demonstrates

 

In humid environments, the thermal design of the enclosure is as important as the equipment it houses. Single-wall cabinets expose internal components to the full range of daily temperature swings, accelerating wear and promoting condensation.

 

Double-layer construction with PEF insulation provides a passive thermal buffer that stabilizes the internal environment and reduces condensation risk. For sites with higher heat loads, the same cabinet platform can be upgraded with active cooling, allowing operators to standardize on a single enclosure design while adapting the thermal strategy to each site's requirements.